Free template
Supplier complaint management: from defect to closed 8D
How to handle a supplier complaint from detection to closure: documentation, containment, corrective action request, 8D review, costs and evaluation.
A supplier complaint starts when you find that something a supplier delivered does not meet your requirements, and ends when the supplier has removed the cause and you have verified it. In between are a handful of steps that decide whether the problem disappears or comes back. This page shows the process as a quality manager runs it, with the documents and tools for each step.
The process at a glance
| Step | What happens | Document |
|---|---|---|
| 1. Detect | Defect found in incoming inspection, production or at your customer | |
| 2. Document and contain | Describe the defect, block affected parts, decide what happens to them | Non-conformance report (NCR) |
| 3. Request action | Formally ask the supplier for containment and corrective action, with dates | Corrective action request (SCAR) |
| 4. Supplier responds | Containment confirmation, then root cause and corrective actions | 8D report |
| 5. Review | Check root causes, actions and proof of effectiveness | |
| 6. Settle costs | Sorting, rework, replacement, compensation | |
| 7. Close and evaluate | Close the case; the complaint feeds into the supplier’s score | Supplier evaluation |
1–2. Detect, document, contain
Record the defect immediately and with facts: part number, lot, quantity checked and quantity defective, the requirement and what you measured, photos. Block the affected parts physically and in your system. Decide the disposition (return, sort, rework, use as is with approval, scrap); in regulated industries such as aerospace, “use as is” may need customer approval.
3. Request corrective action
For significant problems, send the supplier a formal corrective action request with two deadlines: containment confirmation (usually 24–48 hours) and the 8D response. Keep it factual: requirement, finding, evidence. Leave the root cause to the supplier.
4–5. Review the supplier’s 8D
Most of the value of a complaint comes from this step, and most companies skip it. Check:
- Is the problem description the same problem you complained about?
- Are both root causes found: why it happened and why it was not detected?
- Was the root cause verified, or just assumed?
- Do the corrective actions address each root cause, and is the effectiveness proven with data?
- Did the supplier check similar parts and processes (D7)?
If not, send the 8D back with specific questions. Accepting weak 8D reports teaches suppliers that weak 8D reports are enough. The 8D guide lists the typical weaknesses.
The most common reason I send an 8D back: the root cause is not a root cause. “Operator error” or “wrong setting” describes what happened, not why the process allowed it. If the supplier has not understood the problem, the corrective action will not prevent it from happening again, so there is no point accepting the rest of the report.
6. Costs
Which costs the supplier carries (sorting, rework, extra inspection, replacement shipments, costs at your customer) is in practice often decided case by case. For established supply relationships it belongs in the quality agreement, so each complaint does not turn into a negotiation. Write that clause carefully: a fixed list of cost types or a cap can limit you later, for example when a defect causes costs at your own customer that nobody foresaw. Keep a general rule that the supplier carries the costs its non-conformance causes, and use the list only as examples.
7. Close and feed the evaluation
Close the complaint when the 8D is accepted and the actions are validated. Every complaint should change the supplier’s evaluation: the number and severity of complaints, whether they were closed on time and whether the 8D was complete are three of the criteria in our supplier evaluation model. That is how a complaint becomes visible in the supplier’s grade and on the approved supplier list.
Typical weaknesses in supplier complaint handling
- Complaints are kept in a separate spreadsheet and never reach the supplier evaluation.
- No deadlines, so cases stay open for months.
- 8D reports are filed without review.
- Containment is never lifted, so extra inspection costs continue indefinitely.
- Repeated complaints for the same problem are not recognised as repeats.
FAQ
What is the difference between a supplier complaint and a customer complaint?
A supplier complaint is one you raise against your supplier; a customer complaint is raised against you by your customer. The process is mirrored: in a customer complaint, you write the 8D.
How long should a supplier complaint take?
Containment within one or two days, root cause and corrective actions within a few weeks, validation as soon as enough production data exists. Set the deadlines in your quality agreement.
How do I track open supplier complaints?
A simple list works for a few cases. With more suppliers, a tool that links the complaint, the 8D and the supplier evaluation saves time; that is what Suppliscore does.